AutoTURN Online Help
Parking Tools / Quick Draw Row of Stalls
Quick Draw Row of Stalls

Creates a row of parking stalls between picked points. This tool uses the settings specified in the Settings and Dimensions tabs.

To Quick Draw a Row of Stalls:

  1. On the Parking Tools toolbar, click Quick Draw Row of Stalls. The Quick Draw Row of Stalls dialog box displays.
  2. In the drawing, pick a start point for the row.
  3. Move the mouse away from the start point, and then pick an end point.
  4. (Optional) Continue generating another row section by moving the mouse away from the last end point and picking an end point for this section. Repeat this step to generate more sections until the row is completed.
  5. When you have finished generating the row, click the Finish button or right-click, and then click Finish on the shortcut menu.

Settings

Use this tab to define the settings for generating or editing rows of stalls (see Quick Draw Row of Stalls, Add Stalls to Element, or Edit Element).

Stall Type

To select a stall type, click one of the following buttons.

Stall Side

To select the orientation of the parking row relative to the row centerline and/or to have parking stalls only on one side of the row, click one of the following buttons.

Note: The Left and Right settings are based on the vector direction determined by the start and end points of the row, not on your left or right.

Align Sides

Aligns the left side stalls with the right side stalls in a double sided row.

Note: The alignment only occurs within the row. This setting does not align the stalls between two or more rows in a lot.

Stall Direction

Changes the open direction of angled stalls. This setting reverses the traffic flow direction between the rows. It can be used with layouts that employ angles other than 90 degrees.

Wheel Stops

Toggles the generation of wheel stops within the stalls.

End Islands

Toggles the generation of islands at the row ends.

Stall Justification

Minimum End Island Width

Defines the minimum width of end islands.

Line Thickness

Defines the thickness of the stall and spine lines.

Dimensions

Use this tab to define the parking stall dimensions for generating or editing rows of stalls (see Quick Draw Row of Stalls, Add Stalls to Element, or Edit Element).

AutoTURN Online incorporates parking stall dimensions based on published standards from multiple jurisdictions. You can select the appropriate standard for your region, or you can define your own custom dimensions.

Standard Dimensions

To select a parking standard, click the desired parking standard in the list. The Stall Angle, Vehicle Size, and Parking Class lists will change to display the parameters available for the selected parking standard.

Stall Angle

Sets the angle at which stalls are generated in a row relative to the row centerline.

Vehicle Size

Sets the vehicle size for the generated stalls. The vehicle size is a classification of the general size of the vehicles intended to use the stalls in a layout.

Parking Class

Sets the parking class for the generated stalls. The parking class usually identifies typical stall widths associated with turnover/user characteristics.

Aisle Type

Defines whether the traffic accessing the parking stalls will be coming from one direction only ( One Way) or from both directions ( Two Way). This setting affects the Aisle Width value (see Aisle Width below) as the two-way traffic may require a larger aisle width to allow vehicles to pass. When rows are generated, they will be placed at the aisle distance as defined by the layout of the currently selected parking standard.

Stall Length

Displays the length of the parking stall as measured along the stall line.

Stall Width

Displays the perpendicular distance between two stall lines.

Aisle Width

Displays the distance between the access line and the end of the stall lines. The aisle width depends on whether the aisle type is set to One Way or Two Way (see Aisle Type above). The aisle width for both one-way and two-way traffic is defined by the layout of the currently selected parking standard. In some cases, the One Way and the Two Way values are the same.

Custom Dimensions

Defines custom dimensions (Stall Angle, Stall Length, Stall Width, and Aisle Width).

Stall Angle

Sets the angle at which stalls are generated in a row relative to the row centerline.

Stall Length

Sets the length of the parking stall as measured along the stall line.

Stall Width

Sets the distance measured perpendicularly between two stall lines.

Aisle Width

Sets the distance required for vehicles to navigate into and out of parking stalls and for driving between rows of stalls.